induro® XL2 Floor Lacquer

An extremely tough yet flexible fast-drying waterborne polyurethane two pack varnish offering enhanced chemical and mechanical resistance. XL2 is perfect for solid and engineered wood floors with medium to high traffic where high resistance to scuffs, spills and abrasions is required. Noted for its natural clarity, woodwarming and non-yellowing properties. This product is in scope 2004/42/EC.

Use after sealing with induro® GP Seal or ISO Seal for a strong yet flexible varnish. Maintain XL2 with induro® Maintenance products.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring varnishing will have to be sanded. Newly laid floors are sanded to achieve a nice level floor and old floors are sanded to remove existing finishes and to level out worn and heavily used areas.

Sanding will have to be carried out in several grit stages and this will be dependent on the unevenness and general condition of the floor.

Staining

Morrells standard Light Fast range of stains give excellent grain definition and overall colour. Due to this range being spirit based (fast drying), care should be taken on application not to stain too large an area at once as this could lead to a patchy appearance once the stain is dry.

  1. Stain should be applied by brush/rag or mohair pad
  2. Remove excesses with a clean rag

It is important to remove as much of excess stain as possible so as not to create a film as this could result in poor adhesion of subsequent coats of lacquer.

Stains intended for other uses i.e. decking, fencing, garden furniture etc should not be considered for floors as these will contain water-repelling properties, and therefore water based floor lacquers would not adhere to these stains.

Application Guidelines

  1. Do not denib the sealer
  2. Denib between coats of induro® XL2
  3. mix 9 parts lacquer to 1 part 8CAT/INDURO by volume
  4. add catalyst into the can of lacquer, replace top, turn upside down and shake vigorously for 1 minute
  5. allow lacquer to stand for 5 minutes before use (use within 5 hours of mixing)
  6. apply using a short mohair roller or similar, or mohair flooring pad or t-bar applicator
  7. apply lacquer evenly making smooth passes, predominantly along the grain
  8. avoid pooling of lacquer

induro® Application Tips

  1. avoid equipment containing copper, iron, zinc, aluminium and platinum
  2. carry out an adhesion test on a small test area when overcoating non-induro® flooring products
  3. use equipment solely nominated for waterborne products only
  4. not suitable for pulling over
  5. optimum application between 18°C and 22°C with good air movement and ventilation
  6. for professional use only

Application

  1. After 80-100 grit sanding stage, mix induro® Mix'n'Fill with sanding dust and fill gaps smaller than 6mm
  2. Fill gaps larger than 6mm with Hot-Melt Filler or Morrells® One-Part or Two-Part Filler
  3. Complete the sanding regime

Domestic finish

  1. 1 coat of induro® GP Floor Sealer and Primer at 130-150ml per m2 (Dry Film Thickness ~ 42μm)
  2. Do not sand or denib the sealer coat
  3. First coat of induro® XL2 Floor Lacquer at 100-120ml per m2 (Dry Film Thickness ~ 30-35μm)
  4. Lightly sand the coat with rotary sander 150 - 180 grit mesh
  5. Sweep and vacuum the floor
  6. Last coat of induro® XL2 Floor Lacquer at 100-120ml per m2 (Dry Film Thickness ~ 30-35μm)

Commercial finish

  1. 1 coat of induro® GP Floor Sealer and Primer at 130-150ml per m2 (Dry Film Thickness ~ 42μm)
  2. Do not sand or denib the sealer coat
  3. Between each coat of XL2, lightly sand with rotary sander 150-180 grit mesh then vacuum and sweep the floor
  4. 3 to 4 coats of induro® XL2 Floor Lacquer at 100-120ml per m2 (Dry Film Thickness ~ 35-40μm)

  • Pack size: 5L
  • Catalysis: 9 parts lacquer : 1 part catalyst by volume
  • Pot life: 5 hours
  • Touch dry: 20 - 30 minutes @ 18°C
  • Recoatable: 2 - 3 hours minimum @ 18°C
  • Coats (domestic): 2 - 3 coats
  • Coats (commercial): 3 - 4 coats
  • Light Use: 24 hours @ 18°C
  • Fully Hard: 5 - 7 days @ 18°C
  • Traffic: medium - high traffic once fully hard
  • Coverage: 60m² per 5 litres dependent upon the size, orientation and surface quality of the item being coated

Product Codes

8GL/304B induro XL2 90% sheen clear
8SA/304B induro XL2 50% sheen clear
8SM/304B induro XL2 30% sheen clear
8MA/304B induro XL2 10% sheen clear
8CAT/INDURO Catalyst for Induro XL2

MSDS

Visit our Data Sheet page for access to all available data sheets.

Input your information below to begin download.